The Mer Wiki now uses your Mer user account and password (create account on https://bugs.merproject.org/)


Community Workspace/Tegra3

From Mer Wiki
Jump to: navigation, search

Contents

Mer on Tegra3

DISCLAIMER: This project is not endorsed or supported by any company. This is purely a community based effort.

This page describes the Tegra3 common parts. For the device specific notes, check the Tegra3 section in Community_Workspace.

The hardware adaptation is maintained in the project nemo:devel:hw:nv:tegra3:common

Working

  • X.Org with HW accelerated 2D
  • OpenGL ES 1 & 2 (including X.Org support)
  • Gstreamer with HW accelerated video and audio encode/decode/render
    • At least H.264/MPEG4 and AAC are supported
    • For XV sink one must use nvxvimagesink when using a HW decoder.
    • Using nvxvimagesink instead of the de-facto xvimagesink needs patched Qt

Not working

  •  ?

Target Platform Development Using SB2

(Copied from Community_Workspace/RaspberryPi)

Cross-compiling on the host SDK (as opposed to compiling natively on device) is possible by creating a target (an unpacked rootfs) and using sb2 to "emulate" the ARM device.

Install proper SB2 related tools:

sudo zypper in -t pattern Mer-SB2-armv7hl

Step-by-step Setup

Step one is to create the target rootfs. This can be done with mic using the same kickstart file used to create the image:

sudo mic create fs tegra3-image.ks -o /path/to/target --arch=armv7hl

This will create a /path/to/target/tegra3-image directory with a rootfs that contains all the default packages from that ks.

Step two is changing the permissions so we can write anywhere on the rootfs:

sudo chown -R $USER.mer tegra3-image

Step three is initializing the sb2 target (yes, a lot of options there):

cd tegra3-image
sb2-init -A armv7hl -M armv7hl -d -L --sysroot=/ -C --sysroot=/ -c /usr/bin/qemu-arm-dynamic -m sdk-build -n -N -t / tegra3 /opt/cross/bin/armv7hl-meego-linux-gnueabi-gcc

There will be errors from sb2-init (concerning ld and host-gcc), but it should be safe to ignore them.

Step four is to fix a quirk about /var/run in the target being a symlink, sb2 doesn't like this:

rm var/run
mkdir var/run

And another quirk:

echo -n 'armv7hl-meego-linux' > etc/rpm/platform
echo 'arch = armv7hl' >> etc/zypp/zypp.conf

Step five is to rebuild and refresh the packaging system so we can install devel packages:

sb2 -t tegra3 -m sdk-install -R rpm --rebuilddb
sb2 -t tegra3 -m sdk-install -R zypper ref

Building with SB2

Install some build tools and dependencies inside the new SB2 target:

sb2 -m sdk-install -R zypper install gcc make gst-plugins-base-devel gstreamer-devel qt-qmake libqt-devel libqtopengl-devel graphics-adaptation-tegra3-devel graphics-adaptation-tegra3-libEGL-devel graphics-adaptation-tegra3-libGLESv1-devel graphics-adaptation-tegra3-libGLESv2-devel graphics-adaptation-tegra3-libOMX-devel

NOTE: sometimes it's necessary to be on the top directory of the target to successfully run commands in the sdk-install mode. If a command fails mysteriously, try that first.

Build the project:

cd project
sb2 -t tegra3 qmake -recursive
sb2 -t tegra3 make
Personal tools